How To Repair Wells Cago Trailer Side Panels

Gear up the Surface

Fix the surface with Septone Wax & Grease Remover to ensure all clay, grease oil & contaminants are removed.

Permit dry out completely.

Handy Tip: Cut away damaged area & loose pieces.

Sand the Surface

Sand the surface with sandpaper 80 grit to remove all primer, paint, rust or gel-glaze. Sand 2-5cm across damaged area & downwardly to blank metallic or fibreglass.

When possible, both sides of the damaged area should be repaired for added strength. Depress or slightly curve the edges in.

Remove all dust created from sanding with a dry out cloth or compressed air, then re-make clean the surface with Septone Wax & Grease Remover.

Cut the Fibreglass

Cut the fibreglass mat to the required size & allow an extra centimetre around the edges.

On tight curves tear the mat to fit, adding extra pieces if needed.

Put the mat on a make clean surface until ready for use (EG Newspaper).

30 Minute Dominion

Mix no more resin than what you can utilize in 30 minutes.

250ml of resin will cover approximately 0.25m2 of fibreglass matting

Mix Resin Thoroughly

Mix the resin thoroughly with Septone MEKP Catalyst:

For 50mL resin on a cold day, utilise 40 drops of catalyst.

For 50mL of resin on a hot twenty-four hour period, use 20 drops of catalyst.

Brush on Resin

Brush a coat of mixed resin on the damaged area extending five-10cm beyond the repair. Identify the first layer of fibreglass matt onto the mixed resin. Use the pigment brush to saturate the matt with mixed resin. A dabbing movement will help saturate the fibreglass matt & remove whatever air pockets.

Keep applying boosted layers of matting & mixed resin as needed while the offset application is nonetheless sticky & moisture. If the surface dries difficult & is no longer glutinous, sand with fourscore grit sandpaper earlier applying boosted layers of mixed resin & matting.

Follow the aforementioned process if both sides are being repaired.

Allow Area to Cure

Let area to cure, approximately 2 hours at effectually 23-24 degrees.

Curing will take longer at cold temperatures.

In one case cured, sand repaired expanse with dry sandpaper 80 grit.

Clean expanse with Septone Wax & Grease Remover

Apply Car Filler

To return the profile or to smooth out low areas in the surface, use a layer of Septone Auto Filler. Mix Septone Car Filler with hardener thoroughly & apply a thin layer of filler to the repair surface using firm pressure on the applicator to force the filler into all crevices & eliminate whatsoever air pockets.

Gradually utilize the remaining Car Filler until information technology'southward slightly college than the edge of the repair.

Leave for 30 Minutes

Allow 20-30 minutes for automobile filler to cure. Sand with 180 grit sandpaper.

Ensure you feather the edges. Re-make clean with Septone Wax & Grease Remover.

Mask off Area

Mask off the repair expanse in training of the primer glaze.

Apply Septone Acrylic Primer Filler over the repair expanse in thin layers, 3-4 coats.

Leave 5 minutes dry time between each coat.

Later the final glaze get out to dry for 4 hours or overnight.

Remove Masking Tape

Remove all masking tape/newspaper & commencement sanding repaired surface area with wet & dry 1200 grit sandpaper. Plume edges & sand until smooth.

Clean off Wax & Grease Remover

Clean the Septone Wax & Grease Remover.

Your repair is now ready for application of a coloured basecoat.

Select a basecoat colour matched to your original vehicle paint code & apply as directed on the dorsum of the can.

Select the Correct Basecoat

When selecting a base coat, make sure you bank check out the "ColorSpec Pigment Mixing" services offered in store while y'all wait!

Source: https://www.supercheapauto.com.au/blog/paint-panel/repairing-fibreglass.html

Posted by: escobedogerry1946.blogspot.com